« previous next »
Pages: [1] 2 3   Go Down

Author Topic: Helping a buddy can’t lower boost.  (Read 11546 times)

0 Members and 2 Guests are viewing this topic.

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Helping a buddy can’t lower boost.
« on: May 05 2019, 02:35:38 PM »
Car has had a new turbo 6262 added and a Lorenz controller TH style downpipe.
Puck moves freely and all hoses are new.
Installed a powerlogger for him and said I would help setup a decent tune in it.
Power logger and boost gauge both read the same
28-29 psi. (Car ran like a raped ape)
Cranked the boost controller back as far as I could no change.  Loosened the actuator 1/4 inch there was slack no change. Unhooked the boost controller went tuner style no change.
I might try a lighter can if I can find one local.
Boost pressure not getting to the can perhaps?
Any other ideas?


Sent from my iPhone using Tapatalk Pro
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Helping a buddy can’t lower boost.
« Reply #1 on: May 05 2019, 02:40:44 PM »
Hook it up tuner style and see if by it drops down

It
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Helping a buddy can’t lower boost.
« Reply #2 on: May 05 2019, 03:09:57 PM »
I tried that Steve no change.
That was was what made me think there is no boost getting to the can
One thing I did not try but should have was unhook the actuator.


Sent from my iPhone using Tapatalk Pro
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline Forzfed

  • Turbo Street Eliminator
  • ******
  • Posts: 1341
  • PSI: 5
  • Boost n00b
    • View Profile
Re: Helping a buddy can’t lower boost.
« Reply #3 on: May 05 2019, 05:20:41 PM »
Make sure the hose isn't pinch off or the controller is installed backwards.
Logged

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Helping a buddy can’t lower boost.
« Reply #4 on: May 05 2019, 05:53:16 PM »
first trying pumping a little air with a mitey mite or something similar that is around 20 psi and see if the actuator is working...and then your idea of removing the arm
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Helping a buddy can’t lower boost.
« Reply #5 on: May 05 2019, 07:10:36 PM »
Ok so far tested the can with air it seems to work as it should.
Looked at the fitting and casting of the turbo they seem good no blockage
A test with the actuator disconnected is in the works. 
This downpipe was on the old turbo worked well then.



Sent from my iPhone using Tapatalk Pro
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline nocooler

  • Administrator
  • Turbo Street Eliminator
  • ******
  • Posts: 1836
  • PSI: 3
    • View Profile
Re: Helping a buddy can’t lower boost.
« Reply #6 on: May 05 2019, 07:24:24 PM »
How big is the wastegate hole? Sometimes they need opened up
Logged
IhaveaV8

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Helping a buddy can’t lower boost.
« Reply #7 on: May 05 2019, 09:11:03 PM »
I did not install the turbo so I’m not sure. Once I hear back on the test with the actuator off I will have to pull the downpipe and see hope it’s not that hate pulling apart a brand new turbo to port the exhaust.
I got the exact turbo on mine with an external gate I can get the boost down to 14psi.


Sent from my iPhone using Tapatalk Pro
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline gusszgs

  • Turbo Street Modified
  • *****
  • Posts: 431
  • PSI: 1
  • Limited quick brick
    • View Profile
Re: Helping a buddy can’t lower boost.
« Reply #8 on: May 06 2019, 01:16:17 AM »
Take a very good close look at the vacuum lines from turbo to Y
Logged
Jim
1987 T Limited

Offline reality

  • Turbo Street Modified
  • *****
  • Posts: 546
  • PSI: 0
  • Boost n00b
    • View Profile
Re: Helping a buddy can’t lower boost.
« Reply #9 on: May 06 2019, 07:11:33 AM »
Is the puck opening?
Logged

Offline good2win22

  • Turbo Street Outlaw
  • *******
  • Posts: 2019
  • PSI: 0
  • No man lives happily lest he remove the boredom
    • View Profile
Re: Helping a buddy can’t lower boost.
« Reply #10 on: May 06 2019, 07:12:49 AM »
Wire the puck open and drive it. See how much boost builds with the puck wired open. If it’s above 10 psi, you need to open up the hole.  Helps to blend the turn to the waste gate hole as well. My 6262 with a .63 housing did the same thing when I first installed it.
Logged
Jason

1966 Ford Ranch Wagon
1982 Jeep Wagoneer Limited
1986 Grand National BLK PHNX
1987 Turbo Regal Limited
2018 Ram 2500 Cummins

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Helping a buddy can’t lower boost.
« Reply #11 on: May 06 2019, 10:15:36 AM »
 :cheers: :cheers: :cheers: :rock:
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline TexasT

  • Legend in my own mind
  • Turbo Street Outlaw
  • *******
  • Posts: 2171
  • PSI: 1
  • So, This black car is fast?
    • View Profile
Re: Helping a buddy can’t lower boost.
« Reply #12 on: May 06 2019, 04:45:21 PM »
I think I pull that housing off and see if it even has a hole.
Logged
Rich

"Goals without actions are just dreams."

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Re: Helping a buddy can’t lower boost.
« Reply #13 on: May 06 2019, 05:37:48 PM »
arrg i did not want to pull off the turbo or take it apart....  its a very shinny car means I gotta be careful and clean I'm a farmer  :O
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Helping a buddy can’t lower boost.
« Reply #14 on: May 06 2019, 07:01:24 PM »
If you have the right tool, you should be able to do it on the car
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.
Pages: [1] 2 3   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal