Author Topic: Adjustable upper arms  (Read 5655 times)

0 Members and 1 Guest are viewing this topic.

Offline Tim Hensley

  • Turbo Street Modified
  • *****
  • Posts: 330
  • PSI: 0
  • Boost n00b
    • View Profile
Adjustable upper arms
« on: May 02 2019, 02:29:27 AM »
at what ET will adjustable upper help your 60 foot time?
Car sitting centered on frame, proudly one of the few.
I only make enough HP to go high 11s.
I ask because it’s been 3 mouths since my last new purchase for this car and I need to keep my wife use to my bad habit,I go any longer and she’ll think something wrong.
Arizona GN109 forged rotating assembly
DLS 210-210
Champion irons
Extreme Auto stage II trans and converter

Offline ss/gn

  • Bone Stock
  • **
  • Posts: 77
  • PSI: 1
    • View Profile
Re: Adjustable upper arms
« Reply #1 on: May 02 2019, 06:27:06 AM »
Stock with a good bar and shocks have gone 9s.   :powersix:
It's just a six cylinder, you can't loose
Kevin

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Adjustable upper arms
« Reply #2 on: May 02 2019, 08:58:49 AM »
Invest in a fresh tank of gas.  It would be a waste on the upper arms
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Tim Hensley

  • Turbo Street Modified
  • *****
  • Posts: 330
  • PSI: 0
  • Boost n00b
    • View Profile
Re: Adjustable upper arms
« Reply #3 on: May 02 2019, 11:39:31 AM »
Thanks just as I was laying my head down I relived this moment.
Gas is a good suggestion
Arizona GN109 forged rotating assembly
DLS 210-210
Champion irons
Extreme Auto stage II trans and converter

Offline good2win22

  • Turbo Street Outlaw
  • *******
  • Posts: 2019
  • PSI: 0
  • No man lives happily lest he remove the boredom
    • View Profile
Re: Adjustable upper arms
« Reply #4 on: May 02 2019, 01:36:00 PM »
I’ve seen some 1.4ish 60 foot times on stock stuff. A good rear sway bar to keep you straight at launch would be my suggestion
Jason

1966 Ford Ranch Wagon
1982 Jeep Wagoneer Limited
1986 Grand National BLK PHNX
1987 Turbo Regal Limited
2018 Ram 2500 Cummins

Offline Tim Hensley

  • Turbo Street Modified
  • *****
  • Posts: 330
  • PSI: 0
  • Boost n00b
    • View Profile
Re: Adjustable upper arms
« Reply #5 on: May 02 2019, 02:30:22 PM »
I have a Hellwig bar wish I had got the HR bar
But this car goes straight every time. Really my next purchase should Be slicks.
Been running 28X9 Hoosier thinking of MT 28X9 Pro bracket or Et street R
Arizona GN109 forged rotating assembly
DLS 210-210
Champion irons
Extreme Auto stage II trans and converter

Offline gusszgs

  • Turbo Street Modified
  • *****
  • Posts: 431
  • PSI: 1
  • Limited quick brick
    • View Profile
Re: Adjustable upper arms
« Reply #6 on: May 03 2019, 09:25:46 PM »
JMO, but I’m pretty happy with the adjustable UMI uppers I run. Installed properly with the right PL on the PS bar, my car not only lost .12 in the 60’, but also centered up the rear more square and I could eliminate the very small spacer I required on one side. Dropped to high 1.50’s 60’ from struggling to run a 1.7 on same tire and set up.
Jim
1987 T Limited

Offline Top Speed

  • Don't Tread on Me
  • Turbo Street Outlaw
  • *******
  • Posts: 2548
  • PSI: -2
    • View Profile
Re: Adjustable upper arms
« Reply #7 on: May 05 2019, 10:49:05 AM »
Funny I was just thinking about replacing mine with spherical rod ends to eliminate bind.
Champion Irons w/T&D roller rockers, TA-61 turbo, 206/206 Comp Cam,  57 lb/hr Siemens Injectors, 3000 stall PTC, PTE Plenum w/RJC Power Plate, 70 mm Accufab Throttle Body, RJC 325 Megacooler, TurboTweak 5.7/ Alky Control w/M1 methanol, 23 psig on the street, Puddn' Power engine, Borla Exhaust

Chris

Offline Forzfed

  • Turbo Street Eliminator
  • ******
  • Posts: 1341
  • PSI: 5
  • Boost n00b
    • View Profile
Re: Adjustable upper arms
« Reply #8 on: May 05 2019, 01:41:38 PM »
An air bag can help you out a bit too.

JMO, but I’m pretty happy with the adjustable UMI uppers I run. Installed properly with the right PL on the PS bar, my car not only lost .12 in the 60’, but also centered up the rear more square and I could eliminate the very small spacer I required on one side. Dropped to high 1.50’s 60’ from struggling to run a 1.7 on same tire and set up.
Is that with slicks or DR's?


Offline TexasT

  • Legend in my own mind
  • Turbo Street Outlaw
  • *******
  • Posts: 2171
  • PSI: 1
  • So, This black car is fast?
    • View Profile
Re: Adjustable upper arms
« Reply #9 on: May 06 2019, 04:42:53 PM »
DR
Rich

"Goals without actions are just dreams."

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5599
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Re: Adjustable upper arms
« Reply #10 on: May 07 2019, 05:23:26 PM »
Stock uppers, Metco billet lowers, 90/10s up front, QA1 rear single adjustables, ATR rear bar, used 28x9 slicks. 1.5's off the foot brake flashing the convertor to 3950 on a less than stellar track. Suspension tuned by Scoob...of course!
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline phil_long

  • F47
  • Turbo Street Eliminator
  • ******
  • Posts: 1567
  • PSI: 0
  • ...far from avg
    • View Profile
Re: Adjustable upper arms
« Reply #11 on: May 08 2019, 09:51:36 AM »
Loving the idea of looking to keep the wife use to the bad habits. Lol.

Offline Tim Hensley

  • Turbo Street Modified
  • *****
  • Posts: 330
  • PSI: 0
  • Boost n00b
    • View Profile
Re: Adjustable upper arms
« Reply #12 on: May 10 2019, 01:17:41 AM »
Well A new problem has arisen to keep her on her toes.The fuel pump died on a small road trip to Kona.on the return trip home right smack in the middle from Kona  and home the fuse to the fuel pump cut,no spear, picked up a old beer tad and installed it and nothing.$80 dollars for a tow home.
Arizona GN109 forged rotating assembly
DLS 210-210
Champion irons
Extreme Auto stage II trans and converter

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal