« previous next »
Pages: [1]   Go Down

Author Topic: Clean Piston and Frost Plug Question  (Read 4123 times)

0 Members and 6 Guests are viewing this topic.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5599
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Clean Piston and Frost Plug Question
« on: November 02 2015, 05:40:08 PM »
First off...we have the PS rear piston absolutely clean. Head gaskets are intact. Secondly...we have a frost plug in the water jacket behind the PS rear cylinder. Why would the top of the piston be clean...and will the frost plug sitting in the water jacket behind the cylinder affect anything? I doubt we can get it out. This is how the engine was handed to us...how it got there...is a mystery. The short block is mint. Pistons and bearings are mint...and the cylinders still have crosshatch marks on them. Crank end play is within tolerance.
Logged
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Clean Piston and Frost Plug Question
« Reply #1 on: November 02 2015, 05:54:25 PM »
Any cracks? Head or cylinder wall? When I did my first head gasket in the head lifted and the fire ring was intact when I pulled it apart.
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5599
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Re: Clean Piston and Frost Plug Question
« Reply #2 on: November 02 2015, 06:02:31 PM »
Removed the piston/rod...both are fine...and the cylinder is fine as well. I'll have Dan check the head for a noticeable crack or cracks.
Logged
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Clean Piston and Frost Plug Question
« Reply #3 on: November 02 2015, 07:34:02 PM »
that is typically the leanest cylinder.  The power plate was designed to rearrange air flow to bring it in line with the others.
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5599
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Re: Clean Piston and Frost Plug Question
« Reply #4 on: November 03 2015, 02:52:39 AM »
Quote from: Steve Wood on November 02 2015, 07:34:02 PM
that is typically the leanest cylinder.  The power plate was designed to rearrange air flow to bring it in line with the others.

Engine was handed to us with no Power Plate.
Logged
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Clean Piston and Frost Plug Question
« Reply #5 on: November 03 2015, 09:09:49 AM »
so it was definitely lean on that cylinder compared to the others...don't know if that was the full reason, or not
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5599
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Re: Clean Piston and Frost Plug Question
« Reply #6 on: November 03 2015, 07:31:32 PM »
Quote from: Steve Wood on November 03 2015, 09:09:49 AM
so it was definitely lean on that cylinder compared to the others...don't know if that was the full reason, or not

The head gaskets appeared to be intact upon disassembly. Steve...any other reason or reasons that piston would be clean? Injector stuck open...spark plug not firing? Open to suggestions.
Logged
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Clean Piston and Frost Plug Question
« Reply #7 on: November 03 2015, 08:49:31 PM »
Intake manifold gasket sucking water in, there is a port right there?
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5599
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Re: Clean Piston and Frost Plug Question
« Reply #8 on: November 04 2015, 01:58:05 AM »
Quote from: larrym on November 03 2015, 08:49:31 PM
Intake manifold gasket sucking water in, there is a port right there?

I usually put a dab of silicone around the cooling passages when I install an intake. There wasn't any on this one.
Logged
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Clean Piston and Frost Plug Question
« Reply #9 on: November 04 2015, 08:25:04 AM »
You can usually see where it was leaking by but that sounds most plausible to me

Sent from my LG-H810 using Tapatalk

Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.
Pages: [1]   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal