« previous next »
Pages: [1] 2   Go Down

Author Topic: trans temp sensor  (Read 13284 times)

0 Members and 2 Guests are viewing this topic.

Offline Shimy87

  • Turbo Street Eliminator
  • ******
  • Posts: 1248
  • PSI: 2
    • View Profile
trans temp sensor
« on: October 13 2015, 10:59:58 AM »
Does it make a difference if I put the sensor in the lower or upper location on the lines that go to the cooler from the tranny.
Logged
87 GN, K&N cold air, gutted cat, TT 5.7 chip, AFPR, 340 Walbro w/ hotwire, 60 LBS injectors, 981 valve springs, 206/206 Cam, RJC Powerplate, LS1 MAF & translator, Vacuum brakes, Hellwig rear sway bar, Energy suspension poly bushings, Razors Alky, Pypes exhaust, 5931 turbo, CK9.5 converter

Offline TexasT

  • Legend in my own mind
  • Turbo Street Outlaw
  • *******
  • Posts: 2171
  • PSI: 1
  • So, This black car is fast?
    • View Profile
Re: trans temp sensor
« Reply #1 on: October 13 2015, 11:07:57 AM »
The one coming back will be cooler, or at least that is the theory.  I think I would want it in the before the cooler or hotter line. I'd have to look and see which one that is as I don't know right of hand.

If it is an electric gauge you could get another sender and run em both with a switch and see how well the cooler is working.
Logged
Rich

"Goals without actions are just dreams."

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: trans temp sensor
« Reply #2 on: October 13 2015, 11:42:19 AM »
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Shimy87

  • Turbo Street Eliminator
  • ******
  • Posts: 1248
  • PSI: 2
    • View Profile
Re: trans temp sensor
« Reply #3 on: October 13 2015, 12:47:41 PM »
Thanks!!!    :cheers:
Logged
87 GN, K&N cold air, gutted cat, TT 5.7 chip, AFPR, 340 Walbro w/ hotwire, 60 LBS injectors, 981 valve springs, 206/206 Cam, RJC Powerplate, LS1 MAF & translator, Vacuum brakes, Hellwig rear sway bar, Energy suspension poly bushings, Razors Alky, Pypes exhaust, 5931 turbo, CK9.5 converter

Offline Shimy87

  • Turbo Street Eliminator
  • ******
  • Posts: 1248
  • PSI: 2
    • View Profile
Re: trans temp sensor
« Reply #4 on: October 13 2015, 07:10:55 PM »
Got the tranny out this afternoon..... bell housing bolts were a bitch, don't know how I'll get those back in, specifically the pass side top one. Also there is a unconnected ground strap hanging at the top, I assume that belongs on the drivers side top bolt and someone previously didn't put it back.

Stupid question time, can I flip the tranny over to remove the pan and replace filter? Assuming I can but figured id ask?

Thanks!!!
Logged
87 GN, K&N cold air, gutted cat, TT 5.7 chip, AFPR, 340 Walbro w/ hotwire, 60 LBS injectors, 981 valve springs, 206/206 Cam, RJC Powerplate, LS1 MAF & translator, Vacuum brakes, Hellwig rear sway bar, Energy suspension poly bushings, Razors Alky, Pypes exhaust, 5931 turbo, CK9.5 converter

Offline TexasT

  • Legend in my own mind
  • Turbo Street Outlaw
  • *******
  • Posts: 2171
  • PSI: 1
  • So, This black car is fast?
    • View Profile
Re: trans temp sensor
« Reply #5 on: October 13 2015, 08:34:48 PM »
While the trans is out take a bfh and fold down the pinch weld on the trans tunnel. The belt housing bolts will be much easier then.
Logged
Rich

"Goals without actions are just dreams."

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5599
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Re: trans temp sensor
« Reply #6 on: October 13 2015, 08:41:29 PM »
I use a swivel socket for the bellhousing bolts...and a super long extension. Air ratchet makes life easy.
Logged
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline TexasT

  • Legend in my own mind
  • Turbo Street Outlaw
  • *******
  • Posts: 2171
  • PSI: 1
  • So, This black car is fast?
    • View Profile
Re: trans temp sensor
« Reply #7 on: October 13 2015, 08:48:36 PM »
Quote from: Scoobum on October 13 2015, 08:41:29 PM
I use a swivel socket for the bellhousing bolts...and a super long extension. Air ratchet makes life easy.

x2 me too way easier from below.
Logged
Rich

"Goals without actions are just dreams."

Offline Shimy87

  • Turbo Street Eliminator
  • ******
  • Posts: 1248
  • PSI: 2
    • View Profile
Re: trans temp sensor
« Reply #8 on: October 13 2015, 08:59:04 PM »
Yeah I had to use my 2 longest extensions together to get them. Will be buying one long one for installation. Can I flip the tranny to take off pan and change filter? Would be easier but dont know if that would screw up anything....pr obably stupid question :icon_redface:
Logged
87 GN, K&N cold air, gutted cat, TT 5.7 chip, AFPR, 340 Walbro w/ hotwire, 60 LBS injectors, 981 valve springs, 206/206 Cam, RJC Powerplate, LS1 MAF & translator, Vacuum brakes, Hellwig rear sway bar, Energy suspension poly bushings, Razors Alky, Pypes exhaust, 5931 turbo, CK9.5 converter

Offline TexasT

  • Legend in my own mind
  • Turbo Street Outlaw
  • *******
  • Posts: 2171
  • PSI: 1
  • So, This black car is fast?
    • View Profile
Re: trans temp sensor
« Reply #9 on: October 13 2015, 09:03:56 PM »
Get the fluid out or it will exit the vent when you turn it over.
Logged
Rich

"Goals without actions are just dreams."

Offline Shimy87

  • Turbo Street Eliminator
  • ******
  • Posts: 1248
  • PSI: 2
    • View Profile
Re: trans temp sensor
« Reply #10 on: October 13 2015, 09:11:54 PM »
Its all drained...than ks !!
Logged
87 GN, K&N cold air, gutted cat, TT 5.7 chip, AFPR, 340 Walbro w/ hotwire, 60 LBS injectors, 981 valve springs, 206/206 Cam, RJC Powerplate, LS1 MAF & translator, Vacuum brakes, Hellwig rear sway bar, Energy suspension poly bushings, Razors Alky, Pypes exhaust, 5931 turbo, CK9.5 converter

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: trans temp sensor
« Reply #11 on: October 13 2015, 09:33:52 PM »
Buy a long wobble extension and you can get to the upper bolts from the bottom.  Reinstall that ground strap.
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline good2win22

  • Turbo Street Outlaw
  • *******
  • Posts: 2019
  • PSI: 0
  • No man lives happily lest he remove the boredom
    • View Profile
Re: trans temp sensor
« Reply #12 on: October 13 2015, 10:10:18 PM »
Quote from: Steve Wood on October 13 2015, 09:33:52 PM
Buy a long wobble extension and you can get to the upper bolts from the bottom.  Reinstall that ground strap.
Big bump for Steve and installing the ground strap.  You can't have too may of those
Logged
Jason

1966 Ford Ranch Wagon
1982 Jeep Wagoneer Limited
1986 Grand National BLK PHNX
1987 Turbo Regal Limited
2018 Ram 2500 Cummins

Offline Shimy87

  • Turbo Street Eliminator
  • ******
  • Posts: 1248
  • PSI: 2
    • View Profile
Re: trans temp sensor
« Reply #13 on: October 14 2015, 10:09:43 AM »
Are all brands of Dex VI the same? Price ranges by a couple bucks so if so I'll get cheapest
Logged
87 GN, K&N cold air, gutted cat, TT 5.7 chip, AFPR, 340 Walbro w/ hotwire, 60 LBS injectors, 981 valve springs, 206/206 Cam, RJC Powerplate, LS1 MAF & translator, Vacuum brakes, Hellwig rear sway bar, Energy suspension poly bushings, Razors Alky, Pypes exhaust, 5931 turbo, CK9.5 converter

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
trans temp sensor
« Reply #14 on: October 14 2015, 11:13:12 AM »
I use the moble1 from Walmart 😜
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36
Pages: [1] 2   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal