« previous next »
Pages: 1 [2]   Go Down

Author Topic: Actuator?  (Read 7377 times)

0 Members and 3 Guests are viewing this topic.

Offline earlbrown

  • Turbo Street Eliminator
  • ******
  • Posts: 1571
  • PSI: 6
    • View Profile
Re: Actuator?
« Reply #15 on: July 10 2014, 12:54:22 AM »
TPS is steady now. Looks like you found your problem with the flaky voltage.
Logged
'87 GN - 4.2L SFI Turbocharged innercooled V6 - Chrome valve covers - supra pump - 14" K&N - 52mm throttlebody - rocker shaft supports -  1/2 intake spacer - TB coolant bypass - 3" ATR exhaust tip - Alum intake pipe - NOS timing cover - chip - relocated charcoal canister - CR42's - stock

Offline daveismissing

  • Two Buicks- too little money$$
  • Turbo Street Outlaw
  • *******
  • Posts: 6517
  • PSI: 3
  • Two Buicks- too little money$$
    • View Profile
Re: Actuator?
« Reply #16 on: July 10 2014, 11:48:49 AM »
If I followed this correctly- you might want to now log the TPS 5v for a run. You changed the 5v source but what was going on with the old 5V source?
Logged
-Drain plug by Earl Brown, custom oil pan by Rich's Auto

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Actuator?
« Reply #17 on: July 10 2014, 01:50:31 PM »
which is the terminal on the analog block that Bob does not like to use?  Ground or 5v?
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline good2win22

  • Turbo Street Outlaw
  • *******
  • Posts: 2019
  • PSI: 0
  • No man lives happily lest he remove the boredom
    • View Profile
Re: Actuator?
« Reply #18 on: July 10 2014, 03:52:41 PM »
Quote from: daveismissing on July 10 2014, 11:48:49 AM
If I followed this correctly- you might want to now log the TPS 5v for a run. You changed the 5v source but what was going on with the old 5V source?


Original problem was that the boost signal was jumping all around from 20 psi to 10 on the log that was in the first post. I thought that I may have a waste gate actuator that wasn't holding the boost.  Earl asked if I had the MAP sensor power source spliced into the TPS, which I did.  TPS is now back to its original configuration with no Y harness installed. MAP sensor now has a new source for power
Logged
Jason

1966 Ford Ranch Wagon
1982 Jeep Wagoneer Limited
1986 Grand National BLK PHNX
1987 Turbo Regal Limited
2018 Ram 2500 Cummins

Offline good2win22

  • Turbo Street Outlaw
  • *******
  • Posts: 2019
  • PSI: 0
  • No man lives happily lest he remove the boredom
    • View Profile
Re: Actuator?
« Reply #19 on: July 10 2014, 03:55:50 PM »
Quote from: Steve Wood on July 10 2014, 01:50:31 PM
which is the terminal on the analog block that Bob does not like to use?  Ground or 5v?


I hope someone else knows because I'm using both.  I hope it's the ground...
Logged
Jason

1966 Ford Ranch Wagon
1982 Jeep Wagoneer Limited
1986 Grand National BLK PHNX
1987 Turbo Regal Limited
2018 Ram 2500 Cummins

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Actuator?
« Reply #20 on: July 10 2014, 04:19:11 PM »
I believe Bob does not suggest using the PL grd for anything other than very low current devices
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline good2win22

  • Turbo Street Outlaw
  • *******
  • Posts: 2019
  • PSI: 0
  • No man lives happily lest he remove the boredom
    • View Profile
Re: Actuator?
« Reply #21 on: July 10 2014, 10:55:07 PM »
I'll move the ground to the chassis some where
Logged
Jason

1966 Ford Ranch Wagon
1982 Jeep Wagoneer Limited
1986 Grand National BLK PHNX
1987 Turbo Regal Limited
2018 Ram 2500 Cummins
Pages: 1 [2]   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal