Author Topic: Anyone have a 500+ hp GN?  (Read 3670 times)

0 Members and 2 Guests are viewing this topic.

Offline Super Gnat

  • Bone Stock
  • **
  • Posts: 30
  • PSI: 0
  • Boost n00b
    • View Profile
Anyone have a 500+ hp GN?
« on: October 02 2013, 01:34:27 PM »
How did you get there and how much dough are we talking about?


I would love for my GN to be able to compete with the new Camaro ZL1 (580hp), Mustang Shelby GT500 (662hp), and the upcoming Challenger SRT8 "hellcat" (600+hp)..... oh and those damn biturbo AMG mercedes.


My last project was a 2002 Ducati 998 found here, and I think it's time to give the GN some love!




Offline PacecarTA

  • Turbo Street Limited
  • ***
  • Posts: 172
  • PSI: 2
  • im not a newbie
    • View Profile
Re: Anyone have a 500+ hp GN?
« Reply #1 on: October 02 2013, 04:54:08 PM »
500 isnt that difficult
 a TA 49 750
ported irons (champions 1300 )
200r4 with  hipro build,
 9.5 converter (800-950)
downpipe, 400
alky injection 600
injectors and chip 300 (at least 50s)
255 fuel pump (150)
upgrade the axles 300
rear control arm upgrade 300-500
sway br HD  500
shocks 200
tires for track 450


im at 730 or so   still on iron heads

about 15k in motor ,

then a trans to hold it , 2 k for th400, 3-3500 for a 200r4
converter 950109 full forged rotating assembly, th400. ptc converter, alky injection , dual 255lph pumps, fast classic (doable on chip)
rear upgrades , 33 spool, qa1s , swaybar, arms
« Last Edit: October 02 2013, 05:13:11 PM by PacecarTA »
Paul   Magnabuick.com ..NJ rep
86GN pump gas 93/alky 109, iron heads, stock mains, no girdle  9.72 @139
best 1/8 6.13 @ 112 ,best mph 144
https://www.youtube.com/watch?v=vSKzv7ej7Cc
87 GN TTop 109 ,93/alky , 9.82 @ 139 20.6psi , best 1/8th 6.18@113.2
87 GnX'd 
87 GN TTop..stock as can b

Offline Super Gnat

  • Bone Stock
  • **
  • Posts: 30
  • PSI: 0
  • Boost n00b
    • View Profile
Re: Anyone have a 500+ hp GN?
« Reply #2 on: October 02 2013, 05:32:28 PM »
I have a ptc torque converter with a 2800-3200 stall. Its a 10in I believe. I haven't installed it yet. Will this hold up with a high performance motor and built transmission? When I talked to the guys at ptc, they seemed to think that I wouldn't be able to reach the limits of this torque converter. It was like $475. Hmmmm

Offline trashmechlv

  • Turbo Street Limited
  • ***
  • Posts: 129
  • PSI: 0
    • View Profile
Re: Anyone have a 500+ hp GN?
« Reply #3 on: October 02 2013, 06:22:16 PM »
I have the same converter from PTC, woke my car up. I can hold 3000 rpm on the brakes now. I don't have 500hp but was running quicker than those cars listed above at track since they all had stock rear tires and just spun. They were all at high 13 low 14 sec passes spinning. Get your car to hook and tune it good and you will surprise a lot of people who don't have knowledge of the Turbo Buick.
Mike G

87 GN, TA52, ATR headers, 3" downpipe, 80lb inj's and TT 6.1 chip, CAS V4 IC, PTC 9.5 NL, B&M transcooler, stock posi rear 3.42, Hellwig rear bar, Spohn solid LCAs on E85! 11.46@ 115mph

Offline motorhead

  • Turbo Street Outlaw
  • *******
  • Posts: 2267
  • PSI: 4
  • look at my balls... look at them!!!
    • View Profile
Re: Anyone have a 500+ hp GN?
« Reply #4 on: October 02 2013, 07:19:28 PM »
Turbo Buick... horsepower? LOL... you are missing the point, son.

In their natural form these engines make torque, not horsepower.  But, if you have enough cubic dollars you can build one to spin harder to make "horsepower".

Seriously, build a torque monster.
>>>Das Instagram<<<
'80 LeMans Wagon|'87 Monte Carlo SS|'92 Camaro Z28|'07 TrailBlazer SS|'15 Colorado Z71|'19 Hellcat Widebooty M6

Offline phil_long

  • F47
  • Turbo Street Eliminator
  • ******
  • Posts: 1567
  • PSI: 0
  • ...far from avg
    • View Profile
Re: Anyone have a 500+ hp GN?
« Reply #5 on: October 07 2013, 08:04:26 AM »
I second the "torque" comment.  These cars have always been known for TQ over HP.

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal