« previous next »
Pages: [1]   Go Down

Author Topic: Turbosmart Eboost2 boost controller  (Read 4252 times)

0 Members and 1 Guest are viewing this topic.

Offline 2buicks

  • Newbie
  • *
  • Posts: 3
  • PSI: 0
  • Full of Hot Air
    • View Profile
Turbosmart Eboost2 boost controller
« on: February 19 2012, 03:42:01 PM »
Hi, I am a migrant from the other site... :D
 
I have a Hot Air Buick with a FAST XFI (Caspers interface) and I am installing an electronic boost controller and had a few stupid questions...
 
1) Do I need to remove the restrictor in the "T" at the compressor?
2) I obviously can eliminate the wastegate control solenoid as there is no more ecu to control it..?
 
??
Thanks
Greg
Logged
1984 Buick Regal T-Type - FAST XFI, Limit Engineering Turbo, 83lb injectors, Ported Heads, 62mm T/B, Hydraulic Roller, Roller Rockers, JE Pistons, Eagle Rods, Billet Main Caps = too much money spent!!

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Turbosmart Eboost2 boost controller
« Reply #1 on: February 19 2012, 05:39:16 PM »
I have not used one, but,...

I thought it came with it's own solenoid which eliminates the need for a tee if you are using an internal waste gate?  Are you using an external gate?
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5599
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Re: Turbosmart Eboost2 boost controller
« Reply #2 on: February 19 2012, 06:06:54 PM »
I gave Norbs a call about your questions. You need to know what version you have, and may have to have it upgraded to the latest version. He also recommends contacting Cal Hartline.
Logged
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Turbodave

  • Bone Stock
  • **
  • Posts: 89
  • PSI: 0
    • View Profile
Re: Turbosmart Eboost2 boost controller
« Reply #3 on: February 20 2012, 06:36:07 AM »
Why not use the XFI's internal boost control?  Or is yours an older unit?
Logged
TurboDave EWCS(SW) USN (Ret.)
Sevierville, TN
Translator Pro;  MAFless fuel, spark, boost and fuel pump management

86 GN(Translator Pro/Extender Pro/w Boost control, PLX WBO2 (original owner)

Offline 2buicks

  • Newbie
  • *
  • Posts: 3
  • PSI: 0
  • Full of Hot Air
    • View Profile
Re: Turbosmart Eboost2 boost controller
« Reply #4 on: February 20 2012, 11:45:33 AM »
Thanks for the replies...
The XFI is brand new...haven't yet fired the car. I'm just finishing the engine build. I am using an internal wastegate (John Craig Turbo) I wanted a EBC that I could change on the fly. I think I figured it out...(not sure what I was thinking cause the wastegate control has nothing to do with anything anymore =P) I also found a note in the Turbosmart literature about removing the factory restrictors (if any). Thanks for the input everyone - great board!
Logged
1984 Buick Regal T-Type - FAST XFI, Limit Engineering Turbo, 83lb injectors, Ported Heads, 62mm T/B, Hydraulic Roller, Roller Rockers, JE Pistons, Eagle Rods, Billet Main Caps = too much money spent!!

Offline norbs

  • Bone Stock
  • **
  • Posts: 20
  • PSI: 0
  • Boost n00b
    • View Profile
Re: Turbosmart Eboost2 boost controller
« Reply #5 on: March 11 2012, 11:18:42 AM »
Use the fast XFI boost control its going to be best for you..
Logged
Pages: [1]   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal