Author Topic: emblem install  (Read 6563 times)

0 Members and 3 Guests are viewing this topic.

Offline Iownagn-gs

  • Bone Stock
  • **
  • Posts: 30
  • PSI: 0
    • View Profile
emblem install
« on: July 13 2011, 07:30:22 PM »
Does anyone have the correct measurements as to positioning the badges on the fenders and the trunk deck?  I.E.: distance from the fender crease and distance from the door?  That would be good reference as to where to place the Grand National badge and the Intercooled goes just below in line with the GN emblem.  

I think the trunk lid emblem is placed a certain distance from the left side and down from the spoiler.

Offline gordyzx9r

  • Turbo Street Eliminator
  • ******
  • Posts: 1068
  • PSI: 0
  • The Sultan of Swank
    • View Profile
Re: emblem install
« Reply #1 on: July 13 2011, 08:16:59 PM »
Is there a specific measurement for these?  I thought it was somewhat approximated.. .

Offline gordyzx9r

  • Turbo Street Eliminator
  • ******
  • Posts: 1068
  • PSI: 0
  • The Sultan of Swank
    • View Profile
Re: emblem install
« Reply #2 on: July 13 2011, 08:24:06 PM »
Kirban's says 1" from left edge of trunk lid and 3/4" up from top edge of trunk lip molding to base of the 6 in the emblem

It says that the point of the 6 should be 2" from the edge of the fender and about 6" down from the top edge of the fender where it meets the door with the intercooled emblem 2/16" or 3/16" below that.

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5072
  • PSI: 234
    • View Profile
emblem install
« Reply #3 on: July 13 2011, 10:06:10 PM »
Sweet
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

Offline Iownagn-gs

  • Bone Stock
  • **
  • Posts: 30
  • PSI: 0
    • View Profile
Re: emblem install
« Reply #4 on: July 13 2011, 10:37:44 PM »
I'm just trying to get it right the first time. Once they are placed on the car, IMO, there's no going back to do it over without messing up the adhesive backing.

Thanks for the advice.  Your measurements seem to be pretty much on the money.

Offline gordyzx9r

  • Turbo Street Eliminator
  • ******
  • Posts: 1068
  • PSI: 0
  • The Sultan of Swank
    • View Profile
Re: emblem install
« Reply #5 on: July 14 2011, 04:22:00 PM »
I would've sworn there was a diagram for this on gnttype at one time...

Edit:  I have this that I scarfed off of gnttype years ago when it went offline:

Quote
After owning a Turbo Regal and gathering information for the past several years I

Offline Charlief1

  • Just another kinky six
  • Turbo Street Eliminator
  • ******
  • Posts: 1348
  • PSI: 2
    • View Profile
emblem install
« Reply #6 on: July 14 2011, 10:06:36 PM »
Thanks Gordo. That does help if I ever get my T or GN back together.
And remember, when dealing with children, silence may be golden but duct tape is silver.

Offline Top Speed

  • Don't Tread on Me
  • Turbo Street Outlaw
  • *******
  • Posts: 2548
  • PSI: -2
    • View Profile
Re: emblem install
« Reply #7 on: July 15 2011, 06:56:02 PM »
This is the proper location for the TType emblem.
Champion Irons w/T&D roller rockers, TA-61 turbo, 206/206 Comp Cam,  57 lb/hr Siemens Injectors, 3000 stall PTC, PTE Plenum w/RJC Power Plate, 70 mm Accufab Throttle Body, RJC 325 Megacooler, TurboTweak 5.7/ Alky Control w/M1 methanol, 23 psig on the street, Puddn' Power engine, Borla Exhaust

Chris

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5072
  • PSI: 234
    • View Profile
emblem install
« Reply #8 on: July 15 2011, 07:30:12 PM »
Golf cart probably has more miles than your car..
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

Offline Iownagn-gs

  • Bone Stock
  • **
  • Posts: 30
  • PSI: 0
    • View Profile
Re: emblem install
« Reply #9 on: July 15 2011, 09:05:42 PM »
One more for my genius??? :jerkit;   Measured the GN emblem to a "T", but screwed up on the Intercooler emblem.  It's called, not paying attention to what someone tells you.
Anywho, I got precise on the Gn emblem and placed the Intercoller emblem snug, below the GN emblem.  For not having the 1/8" spacing, it looks pretty good IMO.  Sure as heck ain't going to pull it off and re-do.  It is what it is.  Wish that was all I had to worry about.

My thanks goes out again to all the help.  Body shop is going to buff out the area where the GN emblem goes on the trunk lid as there are some very light cloth scratches, then on goes the emblem.  

I'm curious about the bulge emblems, do a lot of guys just leave them off as they appear be a pain to clean and wax around?

Offline daveismissing

  • Two Buicks- too little money$$
  • Turbo Street Outlaw
  • *******
  • Posts: 6517
  • PSI: 3
  • Two Buicks- too little money$$
    • View Profile
emblem install
« Reply #10 on: July 15 2011, 10:48:27 PM »
Many of us have the improved ".8 sfi turbo" emblems.
-Drain plug by Earl Brown, custom oil pan by Rich's Auto

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5072
  • PSI: 234
    • View Profile
Re: emblem install
« Reply #11 on: July 16 2011, 07:34:54 AM »
:phpbbt;
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal