« previous next »
Pages: [1]   Go Down

Author Topic: Oil drain tube  (Read 3067 times)

0 Members and 1 Guest are viewing this topic.

Offline Shimy87

  • Turbo Street Eliminator
  • ******
  • Posts: 1248
  • PSI: 2
    • View Profile
Oil drain tube
« on: August 10 2022, 05:49:43 PM »
This thing has always leaked a bit so got ambitious and decided to put a new gasket in it. Leaks worse now! Going to remove whole thing and see if its cracked....... oil shows up on top of gasket that sticks out a little so don't think its cracked. Maybe its warped a little???  Pain in the ass to get to!!
Logged
87 GN, K&N cold air, gutted cat, TT 5.7 chip, AFPR, 340 Walbro w/ hotwire, 60 LBS injectors, 981 valve springs, 206/206 Cam, RJC Powerplate, LS1 MAF & translator, Vacuum brakes, Hellwig rear sway bar, Energy suspension poly bushings, Razors Alky, Pypes exhaust, 5931 turbo, CK9.5 converter

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Oil drain tube
« Reply #1 on: August 10 2022, 06:05:29 PM »
Turbo drain line?  They often crack and a factory style tube is much better than the steel braided hose aftermarket junk.

Be sure the fitting going into the block is tight.
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Just a Six?

  • OK Now who Farted??
  • Turbo Street Eliminator
  • ******
  • Posts: 1253
  • PSI: 2
    • View Profile
Re: Oil drain tube
« Reply #2 on: August 11 2022, 11:14:15 AM »
File it down if it's not flat.
Logged
David
87 LTD. Purchased May 88
Doeskin leather, coach lites without Landau Roof, moon roof, carpeted trunk & No Factory Hood Ornament!
The sticker on AC shows a V-8 Carb car. Special order by Mr. Nick Hall VP of GM Canada
Runs 11.50 on 21 lbs with my old style 67 Q Trim & Alchy

Offline gnonyx

  • Turbo Street Modified
  • *****
  • Posts: 509
  • PSI: 0
  • Boost n00b
    • View Profile
Re: Oil drain tube
« Reply #3 on: August 11 2022, 12:44:25 PM »
My Throttle Body was leaking a bit and when I checked it it looked like it was slightly wrapped so I place emerald sand paper on top of a piece of glass and the Throttle Body surface came out smooth and level.
Logged
87 GN T-Top, ScanMaster, hot-wire kit, Full Throttle chips w/ matching 60# injectors, adj. fuel pump, and triple pod gauges w/ AEM A/F gauge, oil pressure gauge, vac/boost gauge, Kenne Belle rear seat brace, upgraded tranny w/ Art Carr pan cover, and a pre-lube oil system.

Offline Shimy87

  • Turbo Street Eliminator
  • ******
  • Posts: 1248
  • PSI: 2
    • View Profile
Re: Oil drain tube
« Reply #4 on: August 11 2022, 09:22:33 PM »
Well disconnected from turbo and checked with a straight edge and seemed good, made a new gasket and used some orange hi temp silicone on each side. Put back together, didn't tighten up real tight, let it cure overnight and final tightened it today. Cleaned everything real good with degreaser and water spray.......st ill has a small drip hanging off the lower bolt head. No cracks in pipe.. Looks like I'm going to have to do the sandpaper method to ensure flatness. I can't believe with a gasket and silicone this thing still leaks!!!
Logged
87 GN, K&N cold air, gutted cat, TT 5.7 chip, AFPR, 340 Walbro w/ hotwire, 60 LBS injectors, 981 valve springs, 206/206 Cam, RJC Powerplate, LS1 MAF & translator, Vacuum brakes, Hellwig rear sway bar, Energy suspension poly bushings, Razors Alky, Pypes exhaust, 5931 turbo, CK9.5 converter

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Oil drain tube
« Reply #5 on: August 11 2022, 10:47:00 PM »
I have better luck without silicone.  If I use anything it would be the NASTY permatex aviation 
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline phil_long

  • F47
  • Turbo Street Eliminator
  • ******
  • Posts: 1567
  • PSI: 0
  • ...far from avg
    • View Profile
Re: Oil drain tube
« Reply #6 on: August 12 2022, 12:26:44 AM »
I don't care for the oil drain tube at all Lol
Logged
Pages: [1]   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal