« previous next »
Pages: [1]   Go Down

Author Topic: Priming oil pump thru the cam sensor hole.  (Read 3078 times)

0 Members and 1 Guest are viewing this topic.

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Priming oil pump thru the cam sensor hole.
« on: October 30 2015, 10:44:15 AM »
Any of you young guys that can remember things!  Which way is the correct way to spin the pump drive with a drill?  Counter-clockwise or clockwise?  I want to tell someone the correct way to turn the pump after filling it with oil via the cooler line.
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Priming oil pump thru the cam sensor hole.
« Reply #1 on: October 30 2015, 11:00:09 AM »
I have always spun mine clock wise but I don't have an oil cooler does that matter? Last few times I just filled the filter and the drill did the rest.
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Priming oil pump thru the cam sensor hole.
« Reply #2 on: October 30 2015, 11:08:25 AM »
yeah, I thought it was clockwise.  The oil cooler is a quick trick if you don't want to spin the pump...have to have the adapter on there to do that...so no, it's not important.

Sometimes they don't want to prime even with the filter full...unless the pump was packed with vaseline when installed.  Sometimes they will.
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline larrym

  • Turbo Street Eliminator
  • ******
  • Posts: 1363
  • PSI: 1
    • View Profile
Re: Priming oil pump thru the cam sensor hole.
« Reply #3 on: October 30 2015, 12:52:48 PM »
When I installed my cover rather than use Vaseline I installed my filter and poured lucas break in additive in the cover and turned the pump by hand a couple times till I had fluid on both sides  of the cover installed it and spun it with the drill worked pretty slick and its not as messy as it sounds if the motor is on a stand.
Logged
86 white T type with t tops and blackout trim. 60lb injectors Gen 2 with Extender Chip TR6 ignition 212/206 roller cam Turbonetics BB CPT 61 CAS V4 Intercooler Cobbled together Alky Injection 4 inch MAF pipe with integral sensor
2800 stall lots of fun with a little 6 banger!
Best ET 11.36

Offline dyermullet

  • Turbo Street Limited
  • ***
  • Posts: 159
  • PSI: 0
  • Boost n00b
    • View Profile
Re: Priming oil pump thru the cam sensor hole.
« Reply #4 on: October 30 2015, 01:56:47 PM »
I did mine on the stand, and forgot about the pressure switch.  When I shot oil onto the man door going into the house I knew I had the correct direction. Then I had to find a pipe plug.
Logged

Offline good2win22

  • Turbo Street Outlaw
  • *******
  • Posts: 2019
  • PSI: 0
  • No man lives happily lest he remove the boredom
    • View Profile
Re: Priming oil pump thru the cam sensor hole.
« Reply #5 on: October 30 2015, 01:58:51 PM »
Clockwise like larry mentioned worked for me
Logged
Jason

1966 Ford Ranch Wagon
1982 Jeep Wagoneer Limited
1986 Grand National BLK PHNX
1987 Turbo Regal Limited
2018 Ram 2500 Cummins

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Priming oil pump thru the cam sensor hole.
« Reply #6 on: October 30 2015, 02:44:44 PM »
Quote from: dyermullet on October 30 2015, 01:56:47 PM
I did mine on the stand, and forgot about the pressure switch.  When I shot oil onto the man door going into the house I knew I had the correct direction. Then I had to find a pipe plug.

We must be related!
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5599
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Re: Priming oil pump thru the cam sensor hole.
« Reply #7 on: October 30 2015, 05:11:02 PM »
Clockwise...an d they'll all prime. Dan and I have had a few put up a fight...but the drill eventually 'grabs'.
Logged
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: Priming oil pump thru the cam sensor hole.
« Reply #8 on: October 30 2015, 05:24:37 PM »
I spent 20 minutes one day trying to reprime my car after I had removed the high pressure bypass valve to swap springs.  Maybe if I had spent an hour, it would have primed..or if I had over filled the pan to get the level closer to the pump....so I am not sure they will always prime :D
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5599
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Re: Priming oil pump thru the cam sensor hole.
« Reply #9 on: October 30 2015, 05:29:13 PM »
Dan and I have literally taken turns on the drill getting a few to prime. Some are a real whore. :)
Logged
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon
Pages: [1]   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal