Author Topic: Wheel Bearings  (Read 3615 times)

0 Members and 2 Guests are viewing this topic.

Offline Just a Six?

  • OK Now who Farted??
  • Turbo Street Eliminator
  • ******
  • Posts: 1253
  • PSI: 2
    • View Profile
Wheel Bearings
« on: April 18 2015, 11:05:30 AM »
I'm finally going to do an oil change today before I drop the car off the jack stands I use for winter storage. I picked up some new GM Rotors & Pads about 3 years ago but no bearings included. The bearings on the car now are about 5 years old so can I be Lazy & just reuse them or any reason I shouldn't? Probably won't end up driving it for a week since I need to renew my licence plate sticker & being Late I have to do it In Person!  :013:
David
87 LTD. Purchased May 88
Doeskin leather, coach lites without Landau Roof, moon roof, carpeted trunk & No Factory Hood Ornament!
The sticker on AC shows a V-8 Carb car. Special order by Mr. Nick Hall VP of GM Canada
Runs 11.50 on 21 lbs with my old style 67 Q Trim & Alchy

Offline Charlief1

  • Just another kinky six
  • Turbo Street Eliminator
  • ******
  • Posts: 1348
  • PSI: 2
    • View Profile
Re: Wheel Bearings
« Reply #1 on: April 18 2015, 12:23:22 PM »
Shouldn't be an issue but make sure to clean and inspect them for damage. It's normal to re-use them unless there's some sort of issue.
And remember, when dealing with children, silence may be golden but duct tape is silver.

Offline Just a Six?

  • OK Now who Farted??
  • Turbo Street Eliminator
  • ******
  • Posts: 1253
  • PSI: 2
    • View Profile
Re: Wheel Bearings
« Reply #2 on: April 18 2015, 06:34:22 PM »
Shouldn't be an issue but make sure to clean and inspect them for damage. It's normal to re-use them unless there's some sort of issue.

Thanks but my plans went Way Off Base today when I started checking my 3 storage lockers for the Rotors & I must have sold or given them away?? Then I decided to throw crap into the Recycle Bin. At least a 100 lbs of metal, aluminum, wiring & general Crap not worth trying to give away! Maybe tomorrow I can get to the oil change.  I did find a new set of rear Brake parts with a new rebuild kit & some shoes! :cheers:
David
87 LTD. Purchased May 88
Doeskin leather, coach lites without Landau Roof, moon roof, carpeted trunk & No Factory Hood Ornament!
The sticker on AC shows a V-8 Carb car. Special order by Mr. Nick Hall VP of GM Canada
Runs 11.50 on 21 lbs with my old style 67 Q Trim & Alchy

Offline earlbrown

  • Turbo Street Eliminator
  • ******
  • Posts: 1571
  • PSI: 6
    • View Profile
Re: Wheel Bearings
« Reply #3 on: April 18 2015, 06:58:10 PM »
Bearings aren't that expensive. There's no way I'd reuse an old race.

All it took was doing a bearing job a second time to convince me to spend the extra 10 minutes to replace the races.
'87 GN - 4.2L SFI Turbocharged innercooled V6 - Chrome valve covers - supra pump - 14" K&N - 52mm throttlebody - rocker shaft supports -  1/2 intake spacer - TB coolant bypass - 3" ATR exhaust tip - Alum intake pipe - NOS timing cover - chip - relocated charcoal canister - CR42's - stock

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal