« previous next »
Pages: [1]   Go Down

Author Topic: transmission noise at shift points  (Read 4442 times)

0 Members and 1 Guest are viewing this topic.

Offline TurboCajun

  • Keith Theriot
  • Turbo Street Modified
  • *****
  • Posts: 324
  • PSI: 1
  • 6 Packed
    • View Profile
transmission noise at shift points
« on: July 23 2013, 10:55:52 AM »
after starting the car (trans cold) when putting it in gear I would hear a whinning noise, and after it was up to temp. right before a shift I would hear the same noise. So I pulled the pan to change the filter and oil. I found a bolt laying in the pan, I found the place where it came from( as shown in picture) . put everything back together and no noise. Just wanted to post this for someone hear a whinning noise.
Logged
85 GN -- Converted to 87 set-up using 66/72 turbo, front mount I/C, 80lb injectors,gn1 heads 14 bolt 1.65 roller rockers stud mount, ported intake with plate, fuel hot wire, 3" dp, running 24psi., alky kit, stroker 20 over, 212/206 roller,  best time 10.995 @ 121 1.56 60ft

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: transmission noise at shift points
« Reply #1 on: July 23 2013, 11:24:17 AM »
Thanks!

did you check the torque on the other bolts?
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline TurboCajun

  • Keith Theriot
  • Turbo Street Modified
  • *****
  • Posts: 324
  • PSI: 1
  • 6 Packed
    • View Profile
Re: transmission noise at shift points
« Reply #2 on: July 23 2013, 11:43:50 AM »
sure did  :rock:
Logged
85 GN -- Converted to 87 set-up using 66/72 turbo, front mount I/C, 80lb injectors,gn1 heads 14 bolt 1.65 roller rockers stud mount, ported intake with plate, fuel hot wire, 3" dp, running 24psi., alky kit, stroker 20 over, 212/206 roller,  best time 10.995 @ 121 1.56 60ft

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5072
  • PSI: 234
    • View Profile
Re: transmission noise at shift points
« Reply #3 on: July 24 2013, 05:55:41 PM »
Interesting. I have the same groan. Only does it in gear, can only discern the noise at idle/sitting still.

I'm thinking about my son and I putting a TransGo kit and seeing if we could improve the performance without removing it again. It also won't shift under WOT, you have to lift quickly to get it to go into the next gear. I'm thinking I might see the problem when we pull the governor installing the kit.
Logged
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

Offline TurboCajun

  • Keith Theriot
  • Turbo Street Modified
  • *****
  • Posts: 324
  • PSI: 1
  • 6 Packed
    • View Profile
Re: transmission noise at shift points
« Reply #4 on: July 25 2013, 10:28:08 AM »
I didnt have any problems with it shifting, just the noises right before
Logged
85 GN -- Converted to 87 set-up using 66/72 turbo, front mount I/C, 80lb injectors,gn1 heads 14 bolt 1.65 roller rockers stud mount, ported intake with plate, fuel hot wire, 3" dp, running 24psi., alky kit, stroker 20 over, 212/206 roller,  best time 10.995 @ 121 1.56 60ft
Pages: [1]   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal