Author Topic: Pics of the projects I've done the past couple months.  (Read 2762 times)

0 Members and 1 Guest are viewing this topic.

Offline Jordan_J

  • Bone Stock
  • **
  • Posts: 64
  • PSI: 0
    • View Profile
Pics of the projects I've done the past couple months.
« on: January 07 2011, 05:56:01 PM »
I figured you guys might care. I'm sure I'm wrong though.







Lots of cleaning and paint touch up on the firewall and other places, and replaced lots of old or rusty or worn items. Replaced A/C stuff, fixed my power steering pump, cleaned up the engine wiring quite a bit. And did a spring cleaning while I was at it.


Hydroboost




Got rid of the purple tint for something a little more black. I also refuse to do the back window if I can help it so I will save that for a person who's more of an expert cause the side windows were hard enough.




Ordered a Hughes deep tranny pan since I had a pretty bad leak gasket leak while the car was just sitting in the garage and when I knocked that out I decided to tackle installing my Metco drive shaft loop I've had sitting around for over a year.

I still have an alky install to do but sadly I'm kind of tired of projects so I think I'll hold off on it until closer to spring.
87 Turbo T - 4.1 484 block bored .030 over, Champion ported irons with ported intake, RJC power plate, Elgin 214/224 cam, 6776 turbo with RJC boost controller, stretched SLIC, 3\" THDP, Pypes dual exhaust, 4\" MAF pipe with 14\" K&N and Z06 MAF, 60# Mototrons, hot wired Walbro 340 with KB-BAP, Translator Gen 2 and Extender Extreme chip, Mike Kurtz built 200-4r, PPC 3200 stall, UMI upper and lower control arms, passenger side airbag, any hydroboosted.

20# Boost at 20* timing on 93 octane. No track times yet.

Alky install in progress.

Offline ULYCYC

  • Turbo Street Modified
  • *****
  • Posts: 872
  • PSI: 4
    • View Profile
Re: Pics of the projects I've done the past couple months.
« Reply #1 on: January 07 2011, 06:11:27 PM »
Not the best/safest place for the turbosaver oil filter.  Any leak will spay on the turbo and can flash burn.  Looks  nice other then that.
ED BAKER
87-T, Maplight equipped rear view mirror..
01 Park Ave Ultra S\'charged
BPG#1458

Offline Jordan_J

  • Bone Stock
  • **
  • Posts: 64
  • PSI: 0
    • View Profile
Re: Pics of the projects I've done the past couple months.
« Reply #2 on: January 07 2011, 06:23:02 PM »
Quote from: "ULYCYC @ Fri Jan 07, 2011 6:11 pm"
Not the best/safest place for the turbosaver oil filter.
87 Turbo T - 4.1 484 block bored .030 over, Champion ported irons with ported intake, RJC power plate, Elgin 214/224 cam, 6776 turbo with RJC boost controller, stretched SLIC, 3\" THDP, Pypes dual exhaust, 4\" MAF pipe with 14\" K&N and Z06 MAF, 60# Mototrons, hot wired Walbro 340 with KB-BAP, Translator Gen 2 and Extender Extreme chip, Mike Kurtz built 200-4r, PPC 3200 stall, UMI upper and lower control arms, passenger side airbag, any hydroboosted.

20# Boost at 20* timing on 93 octane. No track times yet.

Alky install in progress.

Offline firebird_1252

  • Turbo Street Modified
  • *****
  • Posts: 576
  • PSI: -1
    • View Profile
Pics of the projects I've done the past couple months.
« Reply #3 on: January 07 2011, 10:14:09 PM »
i love where mine is mounted. it goes right behind the bumper.
87 GN- :D
2011 Jeep Liberty.. its trail rated!

Offline gordyzx9r

  • Turbo Street Eliminator
  • ******
  • Posts: 1068
  • PSI: 0
  • The Sultan of Swank
    • View Profile
Re: Pics of the projects I've done the past couple months.
« Reply #4 on: January 08 2011, 12:23:10 AM »
Quote from: "ULYCYC @ Fri Jan 07, 2011 6:11 pm"
Not the best/safest place for the turbosaver oil filter.

DCEPTCN

  • Guest
Re: Pics of the projects I've done the past couple months.
« Reply #5 on: January 08 2011, 05:49:41 PM »
Looks nice! I'm at the point that if one's valve covers aren't painted black I don't trust him.

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5072
  • PSI: 234
    • View Profile
Pics of the projects I've done the past couple months.
« Reply #6 on: January 08 2011, 05:53:22 PM »
HELL of a job - I really like these threads. I must admit - they make me want to get into my Buick even more.
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

 

SimplePortal 2.3.7 © 2008-2024, SimplePortal