« previous next »
Pages: [1]   Go Down

Author Topic: Broke valve cover bolt  (Read 3838 times)

0 Members and 1 Guest are viewing this topic.

Offline Jordan_J

  • Bone Stock
  • **
  • Posts: 64
  • PSI: 0
    • View Profile
Broke valve cover bolt
« on: December 30 2010, 03:55:45 PM »
The one that goes with the wastegate solenoid in particular, but they are all old and rusty/dirty. Anyone know where I can get a new set or just this one?

Logged
87 Turbo T - 4.1 484 block bored .030 over, Champion ported irons with ported intake, RJC power plate, Elgin 214/224 cam, 6776 turbo with RJC boost controller, stretched SLIC, 3\" THDP, Pypes dual exhaust, 4\" MAF pipe with 14\" K&N and Z06 MAF, 60# Mototrons, hot wired Walbro 340 with KB-BAP, Translator Gen 2 and Extender Extreme chip, Mike Kurtz built 200-4r, PPC 3200 stall, UMI upper and lower control arms, passenger side airbag, any hydroboosted.

20# Boost at 20* timing on 93 octane. No track times yet.

Alky install in progress.

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5072
  • PSI: 234
    • View Profile
Broke valve cover bolt
« Reply #1 on: December 30 2010, 04:53:36 PM »
That happened to me years ago, I think I got on off an old FWD 3.8 at the 'yard.
Logged
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

Offline ULYCYC

  • Turbo Street Modified
  • *****
  • Posts: 872
  • PSI: 4
    • View Profile
Broke valve cover bolt
« Reply #2 on: December 31 2010, 11:04:39 AM »
Try Brian Weavey  at Gbody.com
Logged
ED BAKER
87-T, Maplight equipped rear view mirror..
01 Park Ave Ultra S\'charged
BPG#1458

Offline Jordan_J

  • Bone Stock
  • **
  • Posts: 64
  • PSI: 0
    • View Profile
Re: Broke valve cover bolt
« Reply #3 on: December 31 2010, 09:00:39 PM »
Thanks guys, Dennis Kirban says he has one if it turns out he doesn't I'll ask Brian. Maybe I will hit up Fastenal and see if they can get or make the other screws for me just to have new ones.
Logged
87 Turbo T - 4.1 484 block bored .030 over, Champion ported irons with ported intake, RJC power plate, Elgin 214/224 cam, 6776 turbo with RJC boost controller, stretched SLIC, 3\" THDP, Pypes dual exhaust, 4\" MAF pipe with 14\" K&N and Z06 MAF, 60# Mototrons, hot wired Walbro 340 with KB-BAP, Translator Gen 2 and Extender Extreme chip, Mike Kurtz built 200-4r, PPC 3200 stall, UMI upper and lower control arms, passenger side airbag, any hydroboosted.

20# Boost at 20* timing on 93 octane. No track times yet.

Alky install in progress.

Offline SuperSix

  • Administrator
  • Turbo Street Outlaw
  • *******
  • Posts: 5072
  • PSI: 234
    • View Profile
Broke valve cover bolt
« Reply #4 on: December 31 2010, 09:07:26 PM »
No UPull yards around there?

Is Mike McCoy still selling parts?
Logged
'87 GN, 60lb, TA49, THDP, FTP cam, T+ lots o' shit - SOLD
'07 Ford F150 Lariat 2WD, 5.4L 3v - 255k
'20 Kubota BX2380. FEL, 60" deck
'78 IH/Case 184 Lo-Boy
'99 Kawasaki Bayou 400 4x4

Offline Jordan_J

  • Bone Stock
  • **
  • Posts: 64
  • PSI: 0
    • View Profile
Re: Broke valve cover bolt
« Reply #5 on: December 31 2010, 10:18:04 PM »
There is one really small yard and a larger one about an hour away.
Logged
87 Turbo T - 4.1 484 block bored .030 over, Champion ported irons with ported intake, RJC power plate, Elgin 214/224 cam, 6776 turbo with RJC boost controller, stretched SLIC, 3\" THDP, Pypes dual exhaust, 4\" MAF pipe with 14\" K&N and Z06 MAF, 60# Mototrons, hot wired Walbro 340 with KB-BAP, Translator Gen 2 and Extender Extreme chip, Mike Kurtz built 200-4r, PPC 3200 stall, UMI upper and lower control arms, passenger side airbag, any hydroboosted.

20# Boost at 20* timing on 93 octane. No track times yet.

Alky install in progress.
Pages: [1]   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal