« previous next »
Pages: [1]   Go Down

Author Topic: maf ?  (Read 2810 times)

0 Members and 1 Guest are viewing this topic.

Offline shmed

  • Turbo Street Limited
  • ***
  • Posts: 171
  • PSI: 0
    • View Profile
maf ?
« on: January 25 2015, 03:12:04 PM »
hi just about to order a maf from full throttle an had a question
they list a 3.5 inch maf an a 85 mm maf
my turbo is 4 inch inlet  so would the 3.5 be the better choice for me?
thanks

Logged

Offline Scoobum

  • Turbo Street Outlaw
  • *******
  • Posts: 5599
  • PSI: 3
  • RED-RETIRED EXTREMELY DANGEROUS
    • View Profile
Re: maf ?
« Reply #1 on: January 25 2015, 03:18:52 PM »
I have the 4" setup on my car with the 85 MM Z06 MAF...which requires the 3 to 5 pin adaptor...avai lable from FT. You'll also have to use a different base setting in the Translator...c an't remember which one tho. The Z06 MAF is actually 3.75" if memory serves. I ordered the proper adaptor hose from one of the speed shops up here. Think it was Karbelt.
Logged
Hard work pays off, dreams come true. Bad times don't last, but BAD GUYS do!

RIP Scott Hall AKA Razor Ramon

Offline motorhead

  • Turbo Street Outlaw
  • *******
  • Posts: 2267
  • PSI: 4
  • look at my balls... look at them!!!
    • View Profile
Re: maf ?
« Reply #2 on: January 25 2015, 03:26:53 PM »
Get a 4" MAF tube and C6 ZO6 sensor.  I believe that Full Throttle sells it... here is my build for the TBSS:
http://www.tbssowners.com/forums/showthread.php?t=133002

P/Ns: http://www.tbssowners.com/forums/showthread.php?t=95071

I got everything off Amazon or Summit racing, the aluminum piping and silicone couplers came off eBay.

Don't over spend.
Logged
>>>Das Instagram<<<
'80 LeMans Wagon|'87 Monte Carlo SS|'92 Camaro Z28|'07 TrailBlazer SS|'15 Colorado Z71|'19 Hellcat Widebooty M6

Offline motorhead

  • Turbo Street Outlaw
  • *******
  • Posts: 2267
  • PSI: 4
  • look at my balls... look at them!!!
    • View Profile
Re: maf ?
« Reply #3 on: January 25 2015, 03:31:32 PM »
Logged
>>>Das Instagram<<<
'80 LeMans Wagon|'87 Monte Carlo SS|'92 Camaro Z28|'07 TrailBlazer SS|'15 Colorado Z71|'19 Hellcat Widebooty M6

Offline earlbrown

  • Turbo Street Eliminator
  • ******
  • Posts: 1571
  • PSI: 6
    • View Profile
Re: maf ?
« Reply #4 on: January 26 2015, 04:18:03 AM »
What kind of MAF pipe are you running? That'll kinda dictate what MAF, filter, etc...   you can run.

With a 4" inlet on the turbo are you necking down to 3" or 3.5"?
Logged
'87 GN - 4.2L SFI Turbocharged innercooled V6 - Chrome valve covers - supra pump - 14" K&N - 52mm throttlebody - rocker shaft supports -  1/2 intake spacer - TB coolant bypass - 3" ATR exhaust tip - Alum intake pipe - NOS timing cover - chip - relocated charcoal canister - CR42's - stock

Offline shmed

  • Turbo Street Limited
  • ***
  • Posts: 171
  • PSI: 0
    • View Profile
Re: maf ?
« Reply #5 on: January 26 2015, 06:27:32 PM »
hi earl i have a  4 inch pipe from rjc   
i dont wanna neck down if i don't have to
i do also have the translator regular one i guess.

Logged
Pages: [1]   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal