« previous next »
Pages: [1]   Go Down

Author Topic: cam sensor ?  (Read 2673 times)

0 Members and 1 Guest are viewing this topic.

Offline shmed

  • Turbo Street Limited
  • ***
  • Posts: 171
  • PSI: 0
    • View Profile
cam sensor ?
« on: April 27 2012, 10:01:56 PM »
ok setting my cam sensor followed the instructions on steveds site
question my sensor only reads 6.5 v on my meter and no matter how much i turn it the voltage doesnt change
what the heck am i doing wrong:?
thanks
Logged

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: cam sensor ?
« Reply #1 on: April 27 2012, 10:26:40 PM »
got me.  actual voltage is not important but it must drop
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline daveismissing

  • Two Buicks- too little money$$
  • Turbo Street Outlaw
  • *******
  • Posts: 6517
  • PSI: 3
  • Two Buicks- too little money$$
    • View Profile
Re: cam sensor ?
« Reply #2 on: April 27 2012, 11:09:25 PM »
The wire in "B" does continue on to the ign module?
Logged
-Drain plug by Earl Brown, custom oil pan by Rich's Auto

Offline Just a Six?

  • OK Now who Farted??
  • Turbo Street Eliminator
  • ******
  • Posts: 1253
  • PSI: 2
    • View Profile
Re: cam sensor ?
« Reply #3 on: April 28 2012, 08:23:50 AM »
Its any help you can borrow my caspers tool?
I assume the brass wheel under the cap is tight & spinning as the motor turns over?
Logged
David
87 LTD. Purchased May 88
Doeskin leather, coach lites without Landau Roof, moon roof, carpeted trunk & No Factory Hood Ornament!
The sticker on AC shows a V-8 Carb car. Special order by Mr. Nick Hall VP of GM Canada
Runs 11.50 on 21 lbs with my old style 67 Q Trim & Alchy

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: cam sensor ?
« Reply #4 on: April 28 2012, 09:04:44 AM »
His car runs...therefo re the voltage has to be rising and falling.  B goes to a buffer amplifer in the module
Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.

Offline daveismissing

  • Two Buicks- too little money$$
  • Turbo Street Outlaw
  • *******
  • Posts: 6517
  • PSI: 3
  • Two Buicks- too little money$$
    • View Profile
Re: cam sensor ?
« Reply #5 on: April 28 2012, 09:13:59 AM »
Hall sensors can show funny if they don't have their normal load attached- why I asked.
Logged
-Drain plug by Earl Brown, custom oil pan by Rich's Auto

Offline Steve Wood

  • Turbo Street Outlaw
  • *******
  • Posts: 9950
  • PSI: 34
    • View Profile
    • http://www.vortexbuicks-etc.com/
Re: cam sensor ?
« Reply #6 on: April 28 2012, 09:29:04 AM »
Good point...

don't disconnect the cam sensor while checking voltages....se e the factory diagram at the bottom of the page  http://www.vortexbuicks-etc.com/cam_sensor.htm   The voltage is checked with the cam sensor connector plugged in

Logged
Steve Wood

http://www.vortexbuicks-etc.com

A lot of broken parts does not make you a racer; it makes you a slow learner.
Pages: [1]   Go Up
« previous next »
 
SimplePortal 2.3.7 © 2008-2024, SimplePortal